Home Categories Send inquiry

lte repeater band4 network booster 4g mobile signal booster 2600
  • Introduction
  • Mainfeature
  • Application&scenarios
  • Specification
  • Parts/Warranty
A cell phone signal booster (also known as cellular repeater or amplifier) is a device that boosts cell phone signals to and from your mobile phone whether at home or office or in any vehicle.
It does this by taking the existing cellular signal, amplifying it, and then broadcasting to an area in need of better reception.
A booster kit includes an booster, an indoor antenna and an outdoor antenna, the outdoor antenna can pick up good mobile signal from outside of your house, and send the signal through coaxial cable to the booster, the booster can amplify the signal, then the amplified signal is sent to the indoor antenna, the indoor antenna can transmit the signal into your house, so you can enjoy clearer phone call or faster mobile date inside your house.
 
The consumer repeater is an ideal solution for providing a cost effective improvement in cellular in-building coverage of a home, office, restaurant or building, in the quickest time possible.
Preparing to Buy a Booster:
1. Check your frequency, because different Phone Providers operate on different frequencies and the booster can only work on correct frequency.For more detail, refer to www.unlockonline.com/mobilenetworks.php
2. Make sure that you can place calls on the outside of your home, in the attic, at roof level or wherever you plan to place the Outdoor Antenna. Phonetone can only bring signal into your home when signal reaches the Outdoor Antenna. If there is no signal, the Phonetone will not work for you.
Mainfeature
Main Features:
1. With unique appearance design, have good cooling function
2. With MGC function,(Manual Gain Control), Customer can adjust the Gain as needed ;
3. With DL signal LED display, help to install the outdoor antenna at the best state;
4.With AGC and ALC, make repeater work stable .
5.PCB with isolation function ,make UL and DL signal not influence each other,
6.Low intermodulation, high Gain ,stable Output power
Application&scenarios
22Outdoor antenna ( for receiving the signal from the BTS ) + Cable ( transfering the received signal) + Repeater ( for amplifying the received signal) + cable( for transfering the amplified signal) + indoor antenna( for shooting the amplified signal)
(Note : Omni indoor antenna is 3dBi,it can work with about 200m2 . If need repeater coverage larger area , need add moreantenna,the KT-4G27 Max can work with 8pcs indoor antenna. ( when add antenna ,please remember to take splitters )
Installation Approaches:
Step 1 Start by taking your phone up to the roof or other location outside to find where the signal is strongest.
Step 2 Temporarily mount the Outdoor (outside) antenna in that location. You may need to adjust and move the antenna later.
Step 3 Run coaxial cable into the building to a convenient loaction (attic, etc.) where you can also get standard power for the 3G Signal Booster .
Step 4 Place the Signal Repeater in that location and connect the coaxial cable to the Outdoor Side of the Signal Repeater and the Outdoor antenna.
Step 5 Mount your Indoor (inside) antenna in a productive location. You may need to adjust or move the antenna later. More notes on Indoor antennas and patterns here.
Step 6 Connect coaxial cable between the Indoor antenna and the Signal Repeater output port.
Step 7 Power up the system and check for signal inside the building. If needed, tune system by moving and or pointing the Outdoor and Indoor antennas until they get the most signal possible.
Step 8 Secure all antennas and cables, securely mount the Signal repeater and clean up the installation.
Step 9 Plug power adaptor into AC power socket and finish installation
Specification

Electrical specification

Uplink

Downlink

Frequency Range

4G LTE

2500~ 2570 MHz

2620 ~ 2690MHz

Max .Gain

≥ 70dB

≥ 75dB

Max .Output Power

≥ 24dBm

≥ 27dBm

MGC ( Step Attenuation )

≥ 31dB / 1dB step

Automatic Level Control

≥ 20dB

Gain Flatness

GSM & CDMA

Tpy≤ 6dB(P-P); DCS,PCS ≤ 8dB(P-P)

WCDMA

≤ 2dB/ 3.84MHz,Full Band ≤ 5dB(P-P)

Noise Figure

≤ 5dB

VSWR

≤ 2.0

Group Delay

≤ 1.5μs

Frequency stability

≤ 0.01ppm

Spurious Emission &
Output inter-modulation

GSM Meet ETSI TS 151 026 V 6.1.0

WCDMA Meet 3GPP TS 25.143 ( V 6.2.0 )

CDMA Meet IS95 & CDMA2000

WCDMA System

Spurious Emission Mask

Meet 3GPP TS 25.143 ( V 6.2.0 )

Modulation Accuracy

≤ 12.5%

Peak Code Domain Error

≤ -35dB@Spreading Factor 256

CDMA System

Rho

ρ > 0.980

ACPR

Meet IS95 & CDMA2000

Mechanical Specifications

Standard

I /O Port

N-Female

Impedance

50 ohm

Operating Temperature

-25ºC~+55ºC

Environment Conditions

IP40

Dimensions

155x112x85mm

Weight

≤ 1.50Kg

Power Supply

Input AC90-264V,output DC 5V / 3A

LED Alarm

Standard

Power LED

Power Indicator

UL LED

Be lighted when there is phone calling

DL 1

Be lighted when Outdoor signal is -65dB

DL 2

Be lighted when Outdoor signal only -55dB

DL 3

Be lighted when Outdoor signal only -50dB
Parts/Warranty
2Package Included:
1 * lte repeater band4 network booster 4g mobile signal booster 2600
1 * Power Adapter
1 * Mounting Screw Kit
1 * English User Manual
Note : The product is not including cable,outdoor antenna,indoor antenna,you need to buy extra
■ contat supplier ■ Solution&Application

  • *Model : KTWTP-17-046V *Product Category : (450-470MHz) 17dBi-1.8m grid parabolic antenna

  • *Model : KT-CRP-B5-P33-B *Product Category : UHF 400Mhz 2W Band Selective walkie talkie Repeater

  • *Model : KT-CPS-400-02 *Product Category : 400-470MHz 2-way Cavity splitter

  • *Model : *Product Category :

lte repeater band4 network booster 4g mobile signal booster 2600 Related Video:

Related Products

Low price 2100mhz wcdma repeater mobi...
17-25dBm indoor CDMA 850 cell phone s...
Low price full bar gsm 900mhz signal ...